![replacement serial library vb.net replacement serial library vb.net](https://www.xanthium.in/sites/default/files/site-images/serial-prog-visual-basic/serial-port-programming-debugging-vb.png)
![replacement serial library vb.net replacement serial library vb.net](https://3.bp.blogspot.com/-YFvI-Ix8bQ0/T3NDVJzlgBI/AAAAAAAAAes/2yyTz2nNFAw/s1600/Host+File.png)
- #Replacement serial library vb.net how to
- #Replacement serial library vb.net manual
- #Replacement serial library vb.net software
- #Replacement serial library vb.net code
You can actually test this with the set of speakers, it should RESET the volume/bass/treble etc. Type a letter ‘a’ for example, to send the RESET command and you should see output. Upon connecting you should see the output from the Serial println in the setup() function.
#Replacement serial library vb.net code
We can test the above code by connecting to our COM port using PuTTy, open up PuTTy and enter the COM port that the Arduino is detected on. If the byte matches one in our switch case we send the corresponding command, if not then we throw an unknown command in there. The basics of the sketch are as follows, we detect incoming data on the serial port. Serial.println("Sending Command: VOLUME UP") Serial.println("Sending Command: VOLUME DOWN") Serial.println("Sending Command: BASS DOWN") Serial.println("Sending Command: BASS UP") Serial.println("Sending Command: TREBLE DOWN") Serial.println("Sending Command: TREBLE UP") Serial.println("Sending Command: INPUT2") Serial.println("Sending Command: INPUT1") Serial.println("Sending Command: RESET") Serial.println("Sending Command: TEST 4") Void(* resetFunc) (void) = 0 //declare reset function address 0 * An IR LED must be connected to Arduino PWM pin 3. We’ll be using a simple VB.NET program to communicate with the Arduino, this will write to the serial port and send a byte – In the Arduino sketch we will monitor the serial port for incoming bytes and match them up to the codes that get sent over IR. This works perfectly, as you can push the LED down on the board to make a nice snug fit. Using the Arduino nano, I soldered the resistor to one leg of the IR LED and the other side directly to the Pin on the board. It is a very basic circuit to connect these up.
![replacement serial library vb.net replacement serial library vb.net](https://i.ebayimg.com/images/g/AgYAAOSwytFhJ5IY/s-l1600.jpg)
The next stage is to connect the IR LED and Resistor to the Arduino board.
#Replacement serial library vb.net software
In order for us to communicate with it, we decided that having software on the PCs was the best way to go, we could of made another remote but that would just get lost/misplaced eventually anyway. That is all we need the IR Receiver for, so from now on we’ll disconnect it and carry on with the rest of the project. So we have the data we need to mimic the IR signals of our remote. Now all we need to do is go through the speaker remote and recording the code of each button. The IRRemote library has built-in functions to re-transmit this data. Luckily for us, the protocol used by the speaker remote has been identified as the NEC protocol, 32 bits. (see image below with the IR Receiver connected to a Arduino Uno (for prototyping, you can use the Arduino nano, but you’ll have to upload/reset the sketches when testing) Run the Examples > IRRemote > IRrecvDumpv2 example. We did this by connecting up our IR Receiver to the Arduino, the receiver has 3 pins and from left to right GND, +5V, SIGNAL and using the Arduino IRRemote library. The idea is simple, we capture the IR signal from a remaining speaker remote and record the commands that get transmitted. We decided to make our own speaker remotes, as cheaply as possible.
#Replacement serial library vb.net manual
The speakers do not have any manual controls for the input selection, bass/treble etc. Projector remotes are easy to come by, but the AV-1000 remote is no longer manufactured. We have a set of Vision AV-1000 wall mounted active speakers, connected to an EPSON projector. Usually this wouldn’t be a problem, we’ll just contact the supplier or manufacturer and order replacements. We have sets of speakers and projectors and the users keep losing the remotes, or misplaced/stolen.
#Replacement serial library vb.net how to
It’s something we’ve been looking at for a while and figuring out how to solve it.